데이터 로거

Campbell Scientific GRANITE 9 DAQ - measurement system

• One of the most computationally powerful data-acquisition devices from Campbell Scientific • 24 bit and 32 bit ADC • An all-digital measurement and control DAQ • 8x digital I/O terminals (configurable) • 2x switched 12V • EPI port switch for high-speed connection to all GRANITE modules • Built-in GPS for network synchronization • Built-in Wi-Fi • 4 Mbytes battery-backed SRAM + 128 MB NOR flash memory, expandable to 16 GB • Onboard storage of streaming data with 2 GB of DDR3 SDRAM and 64 GB SSD • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Campbell Scientific GRANITE 10 DAQ - measurement system

• One of the most computationally powerful data-acquisition devices from Campbell Scientific • 24 bit and 32 bit ADC • An all-digital measurement and control DAQ • 8x digital I/O terminals (configurable) • 4 General-purpose CAN channels • 2x switched 12V • EPI port switch for high-speed connection to all GRANITE modules • Built-in GPS for network synchronization • Built-in Wi-Fi • 4 Mbytes battery-backed SRAM + 128 MB NOR flash memory, expandable to 16 GB • Onboard storage of streaming data with 2 GB of DDR3 SDRAM and 64 GB SSD • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Campbell Scientific VOLT 108 - general-purpose, multiplexed analog measurement module

• General-purpose, multiplexed analog measurement module • 8 differential or 16 single-ended input channels with 2 excitation channels • 1x switched 12V and 2x switched 5V • Channel count expansion via the CPI bus • USB 2.0 interface for direct-to-PC-based operation • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Campbell Scientific VOLT 116 - general purpose, multiplexed analog measurement module

• General-purpose, multiplexed analog measurement module • 16 differential or 32 single-ended input channels with 2 excitation channels • 2x switched 12V and 4x switched 5V • Channel count expansion via the CPI bus • USB 2.0 interface for direct-to-PC-based operation • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Campbell Scientific TEMP 120

• Purpose-built thermocouple measurement module • Part of a data-acquisition system such as the GRANITE Datalogger series, CR6 or CR1000X loggers • 20 thermocouple inputs using universal copper-copper standard miniature thermocouple connectors • Resolution of 0.015°C • Handles extreme temperature environments and rapid thermal gradients • Time base can be referenced either to GPS or a temperature-compensated real-time clock • CPI DAQ connection for channel expansion • USB 2.0 interface for PC-based operation • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Campbell Scientific CR1000X - measurement system

• Calibration certificate (standards traceable to U.K.A.S accreditation service) • 16x analogue single-ended or 8 differential Analog Inputs • 10x pulse counters • 8x digital IN/OUT (configurable) • 4x analogue voltage (switched excitation mode or switched regulated voltage supply) • 2x switched 12V • RS232, CS I/O PORT to CSI peripherals, USB, Ethernet (LAN) port • 4 Mbytes battery-backed SRAM + 72 MB flash memory, expandable to 8 GB • Surge, Electrostatic Discharge and Lightning Protection for all critical Inputs and Outputs • Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

CR1000X Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to ilac-MRA accreditation service

Campbell Scientific CR1000 - measurement system

• 16x analogue single-ended or 8 differential IN • 2x digital pulse counters IN • 8x digital IN/OUT • 3x analogue voltage OUT • 1x switched 12V OUT • RS232 • CS I/O PORT, SDI-12, Peripheral ports • CF-card, USB, LAN, WLAN (optional) • 2/4 Mbytes SRAM memory • Surge protection for all Inputs by gas discharge tube (GDT) • Surge protection for critical outputs by GDT or transient voltage suppression diodes • Power feeding protected by transzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

CR1000 Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to ilac-MRA accreditation services

Campbell Scientific CR6 - measurement system

• Calibration certificate • 12x single-ended or 6xy differential freely programmable analog or digital IN & OUT • 4x digital pulse counters IN an/or 4x analog voltage OUT (5 and 3.3V) • 2x switched 12V OUT • 1x RS232 / RS485 • CS I/O PORT • LAN • USB • RJ-45 • Micro-SD card • 4 Mbytes SRAM memory • Surge protection for all Inputs by gas discharge tube (GDT) • Surge protection for critical Oututs by GDT or transient voltage suppression diodes • Power feeding protected by tranzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

Campbell Scientific CR6 - WIFI - measurement system

• CR6-WIFI • Calibration certificate • 12x single-ended or 6xy differential freely programmable analog or digital IN & OUT • 4x digital pulse counters IN an/or 4x analog voltage OUT (5 and 3.3V) • 2x switched 12V OUT • 1x RS232 / RS485 • CS I/O PORT • WLAN WIFI for short-range wireless IP communications based on 802.11 b/g/n, WPA/WPA2-Personal, WPA/WPA2-Enterprise Security, WEP • USB • RJ-45 • Micro-SD card • 4 Mbytes SRAM memory • Surge protection for all Inputs by gas discharge tube (GDT) • Surge protection for critical Oututs by GDT or transient voltage suppression diodes • Power feeding protected by tranzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

Campbell Scientific CR6-RF4XX - measurement system

• CR6-RF422 • Calibration certificate • 12x single-ended or 6xy differential freely programmable analog or digital IN & OUT • 4x digital pulse counters IN an/or 4x analog voltage OUT (5 and 3.3V) • 2x switched 12V OUT • 1x RS232 / RS485 • CS I/O PORT • Internal RF422 morem or optional for specific countries: RF407, RF412, RF451 • LAN • USB • RJ-45 • Micro-SD card • 4 Mbytes SRAM memory • Surge protection for all Inputs by gas discharge tube (GDT) • Surge protection for critical Oututs by GDT or transient voltage suppression diodes • Power feeding protected by tranzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

CR6 (-RF422 / -WIFI) Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to ilac-MRA accreditation service

Campbell Scientific CR310 - measurement system

• Set-up easily with PC software and USB connectivity • Ideal for small applications requiring long-term, remote monitoring and control • Measure smart sensors using RS-232 or SDI-12 • 6x single-ended or 3x differential freely programmable analog or digital IN & OUT • 8x pulse counting terminals with 2x control terminals • 7x configurable digital I/O terminals • 2x switched 12V OUT; 2x voltage excitation terminals • 1x RS232, 1x USB Micro B, 1x 10/100 Ethernet RJ45 • 30MB serial flash memory • Integral surge and ESD protection • Integrated 12 V battery solar charge regulator to charge batteries • Connect with PakBus, Modbus, DNP3, GOES, and other standard communication protocols • Available in multiple radio, cellular network modem and Wi-Fi options that are suitable for different regions and applications

Campbell Scientific CR850 - measurement system

• 6x analog single-ended or 3 differential IN • 2x digital pulse counters IN • 4x digital IN/OUT • 3x analog voltage OUT • 1x switched 12V OUT • RS232 • CS I/O PORT • 2/4 Mbytes SRAM memory • Keypad • LCD Display • Surge protection for all Inputs by gas discharge tube (GDT) • Power feeding protected by tranzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

CR850 Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to ilac-MRA accreditation services

• 6x analog single-ended or 3 differential IN • 2x digital pulse counters IN • 4x digital IN/OUT • 3x analog voltage OUT • 1x switched 12V OUT • RS232 • CS I/O PORT • 2/4 Mbytes SRAM memory • Surge protection for all Inputs by gas discharge tube (GDT) • Power feeding protected by tranzorb diodes • Grounding socket for electrostatic discharge (ESD) protection

CR800 Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to ilac-MRA accreditation services

Ammonit Meteo-40S

• ​Ammonit Meteo-40S • 4x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 1x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 4x pulse counter IN • 2x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 2x analog voltage OUT (5V | Switches) • 1x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Ammonit Meteo-40S Plus

• ​Ammonit Meteo-40S Plus • With new firmware version offering flexibility in the user setttings, sensor and modem configuration, data security, among others • 4x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 1x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 4x pulse counter IN • 2x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 2x analog voltage OUT (5V | Switches) • 1x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Meteo 40-S Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service

Meteo 40-S Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service

Ammonit Meteo-40M

• ​Ammonit Meteo-40M • 8x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 1x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 8x pulse counter IN • 4x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 4x analog voltage OUT (5V | Switches) • 1x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Ammonit Meteo-40M Plus

• ​Ammonit Meteo-40M Plus • With new firmware version offering flexibility in the user setttings, sensor and modem configuration, data security, among others • 8x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 1x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 8x pulse counter IN • 4x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 4x analog voltage OUT (5V | Switches) • 1x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Meteo-40M Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service

Meteo-40M Plus Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service

Ammonit Meteo-40L

• ​Ammonit Meteo-40L • 12x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 2x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 12x pulse counter IN • 8x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 8x analog voltage OUT (5V | Switches) • 2x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Ammonit Meteo-40L Plus

• ​Ammonit Meteo-40L Plus • With new firmware version offering flexibility in the user setttings, sensor and modem configuration, data security, among others • 12x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit) • 2x analog current IN (± 1mA, ± 10mA, ± 100mA 16bit) • 12x pulse counter IN • 8x digital serial status IN • 1 RS485 Master IN (for up to 8 smart sensors or Ultra Sonic Anemometers) • 8x analog voltage OUT (5V | Switches) • 2x analog current OUT • 1 RS485 Slave OUT (SCADA monitoring software) • 3 USB (2x USB-A host, 1x USB-B device) • 1 LAN (Ethernet)

Meteo-40L Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service

Meteo-40L Plus Datalogger Calibration - compliant to recommendations of FGW TR6, IEC and MEASNET

• Compliant to recommendations of FGW TR6, IEC and MEASNET • Incl. calibration certificate • Calibration standards traceable to DAkkS (ilac-MRA) accreditation service